Note:The instructions in this article apply to heating and cooling systems common in the United States and Canada. If you live in the EU and need to troubleshoot your thermostat, please check Manually control heating when Heat Link is disconnected before you begin troubleshooting.
If your Google Nest Thermostat is not receiving power from your heating, ventilation, and air conditioning (HVAC) system, it will tell you there’s a problem. There are a few things you may notice on your thermostat:
- A “No power” or “No system power” alert shouldappear.
- A help code should also appear, such as M20 or E298.
- Some help codes can be dismissed, but they may appear again if the problem persists.
- E help codes can’t be dismissed, so they won’t disappear until the issue is fixed.
- The Settings
icon will also have an exclamation point . If you hover over it, it will say ”Equipment error.” - A “Low battery” or “Very low battery” alert may appear if the backup batteries continue to lose charge.
- Your thermostat may disconnect from Wi-Fi if it’s not receiving power, even if the battery level is good.
. If you hover over it, it will say ”Equipment error.”A “No power” alert can be caused by the following:
- The thermostat wiring is incorrect.
- Your thermostat is connected to a system that requires a C or common wire, but that wire isn’t connected. Some systems, including heat-only, cool-only, zone-controlled, and heat pump systems, require a C wire orNest Power Connector. Go to g.co/nest/cwire for details.
- The HVAC system is powered off at the circuit breaker, fuse box, or system switch, or there’s a power cut.
- The HVAC system is experiencing some other issue that prevents it from sending power to the thermostat wires.
Below are some steps to troubleshoot a “No power” alert on your thermostat:
| This article only applies to the Nest Thermostat.
|
| How to tell which thermostat you have |
Note: If your Nest Thermostat won’t turn on, or if your Nest Thermostat E or Nest Learning Thermostat is having power issues, learn how totroubleshoot when your Nest thermostat won’t turn on.
Before you troubleshoot
- If your thermostat shows a low battery alert, change the batteries first so that you can control your system and stay comfortable while you troubleshoot.
- If you recently turned power off at the circuit breaker of the heating and cooling system, make sure it’s back on.
- If you were installing the Nest Power Connector and there'san N260 help code, confirm that the cover is closed on your HVAC equipment. There is often a safety switch that prevents operation with the cover removed.
Troubleshoot
1. Refer to theequipment information
To narrow down possible causes of a “No power” alert, use your thermostat to navigate to its equipment information.
- If needed, tap the touch bar to wake up your thermostat. Tap again to open the Menu view.Then select Settings .
- Slide on the touch bar to hover over Equipment.
- A “No power” or “No system power” alert shouldappear.
- An Error code (such as E## or N##) should also appear.
2. Check the wiring
On your Nest Thermostat, go to Settings 
Equipment 
Wiring info. Check for wires that appear as grey. This means that the wire is not sending voltage to your thermostat. Some wires, like a C or R wire, need to send voltage to keep your thermostat powered on.
If all the wires are grey, the system may be powered off or experiencing some other power-related issue. Check that the system is powered on at the circuit breaker, fuse box, or system switch.
If any wire is grey, it isn’t electrically detected by your thermostat. This usually happens because the wire isn’t properly connected. It might also mean that the wire was incorrectly entered in the app. Check the system wires to make sure they are correctly entered and properly connected.
Important: You must turn the system off before checking the system wires. This will help prevent damage to them and your thermostat.
- Turn power off for the system. The power switch will usually be in the circuit breaker, fuse box, or system switch. In some homes, it will look like a light switch near the heating or cooling equipment.
- Note: There may be one switch for heating and one for cooling, or a single switch for both.
- Pull your thermostat away from its base to remove it.
- You might want to check that the wires are correctly identified. If they’re not, you’ll need to set up your thermostat again with the correct wiring info.
- To disconnect each wire, push down its connector tab and gently pull out the wire. Then, do the following as needed:
- Straighten the wire end.
- Strip the wire to expose ⅓" to ½" of copper.
- Seat the wire fully into the right connector.
- After all the wires are connected, re-attach your thermostat to its base.
- Turn the power for the system back on.
- After a few moments, use your thermostat to go to the Menu view Equipment, then check if the issue is resolved.
3.Connect a C wire or the Nest Power Connector
Your thermostat may require a C wire or the Nest Power Connector to provide enough consistent power.
- Check whether a C wire or spare wire is available. If you find one, connect it to your thermostat’s C connector.
- If a C wire isn’t available, install the Nest Power Connector or pull a new C wire. Note: A new C wire installation generally requires a pro.
Learn about the common or C wire
4. Contact a local pro
If you think wires are incorrectly connected to your thermostat and want additional help, contact Nest support. You can also read more steps on how to troubleshoot Nest thermostat help codes.
If you think there may be a problem with the heating and cooling system, or your system requires a C wire, contact a local pro.
Was this helpful?
How can we improve it?
Need more help?
Try these next steps:
Have a question?
Get an answer from an expert on the Google Home Help Forum.
